NXQ-L25/10-H,NXQ-L1.6/10-H,NXQ-L2.5/10-H液壓囊式蓄能器，蓄能器膠囊，蓄能器皮囊
NXQ-L150/10-H,NXQ-L150/20-H,NXQ-L150/31.5-H液壓囊式蓄能器，蓄能器膠囊，蓄能器皮囊
NXQ-L150/10-H,NXQ-L150/20-H,NXQ-L150/31.5-H液壓囊式蓄能器，蓄能器膠囊，蓄能器皮囊
NXQ-L25/10-H,NXQ-L1.6/10-H,NXQ-L2.5/10-H囊式蓄能器，蓄能器膠囊，蓄能器皮囊
NXQ-L0.25/10-H,NXQ-L0.4/10-H,NXQ-L0.63/10-H
NXQ-L1/10-H,NXQ-L1.25/10-H,NXQ-L4/10-H
NXQ-L6.3/10-H,NXQ-L16/10-H,NXQ-L20/10-H
NXQ-L25/10-H,NXQ-L1.6/10-H,NXQ-L2.5/10-H
NXQ-L10/10-H,NXQ-L40/10-H,NXQ-L63/10-H
NXQ-L80/10-H,NXQ-L100/10-H,NXQ-L125/10-H
NXQ-L150/10-H,NXQ-L150/20-H,NXQ-L150/31.5-H
NXQ-L0.25/20-H,NXQ-L0.4/20-H,NXQ-L0.63/20-H
NXQ-L1/20-H,NXQ-L1.25/20-H,NXQ-L4/20-H
NXQ-L6.3/20-H,NXQ-L16/20-H,NXQ-L20/20-H
NXQ-L25/20-H,NXQ-L1.6/20-H,NXQ-L2.5/20-H
NXQ-L10/20-H,NXQ-L40/20-H,NXQ-L63/20-H
NXQ-L80/20-H,NXQ-L100/20-H,NXQ-L125/20-H
NXQ-L0.25/31.5-H,NXQ-L0.4/31.5-H,NXQ-L0.63/31.5-H
DZ30-1-50B/100XM抗衡閥
A2F160R1P1,A2F160R2P1,A2F160R3P1,A2F160R4P1,A2F160R1P2,柱塞泵,定量柱塞泵，溫納柱塞泵廠家
A2F160R2P2,A2F160R3P2,A2F160R4P2,A2F160R1P3,A2F160R2P3,柱塞泵,定量柱塞泵，溫納柱塞泵廠家
A2F160R3P3,A2F160R4P3,A2F160R1P4,A2F160R2P4,A2F160R3P4,柱塞泵,定量柱塞泵，溫納柱塞泵廠家
A2F160R4P4,A2F160R1P5,A2F160R2P5A2F160R3P5,A2F160R4P5,柱塞泵,定量柱塞泵，溫納柱塞泵廠家
A2F160R1P6,A2F160R2P6,A2F160R3P6,A2F160R4P6,A2F160R1P7,
A2F160R2P7,A2F160R3P7,A2F160R4P7,A2F160R1Z1,A2F160R2Z1,柱塞泵,定量柱塞泵，溫納柱塞泵廠家
A2F160R3Z1,A2F160R4Z1,A2F160R1Z2A2F160R2Z2,A2F160R3Z2,柱塞泵,定量柱塞泵，溫納柱塞泵廠家
A2F160R4Z2,A2F160R1Z3,A2F160R2Z3,A2F160R3Z3,A2F160R4Z3,柱塞泵,定量柱塞泵，溫納柱塞泵廠家
A2F160R1Z4,A2F160R2Z4,A2F160R3Z4,A2F160R4Z4,A2F160R1Z5,柱塞泵,定量柱塞泵，溫納柱塞泵廠家
帶定位器使用的調節閥，定位器工作不正常，其氣路節流口堵塞是常見的故障。帶定位器工作時，必須處理好氣源，通常采用的辦法是在定位器前氣源管線上安裝空氣過濾減壓閥。增大節流間隙法：如介質中的固體顆?；蚬艿乐斜粵_刷掉的焊渣和銹物等因過不了節流口造成堵塞、卡住等故障，可改用節流間隙大的節流件節流面積為開窗、開口類的閥芯、套筒，因其節流面積集中而不是圓周分布的，故障就能很容易地被排除。如果是單、雙座閥就可將柱塞形閥芯改為V形口的閥芯，或改成套筒閥等。
